 |
|
|
|
Physical Properties (Typical) |
|
| Type Proprietary emulsion polymer |
|
Calculated VOC (less water)2.6 g/L |
| State Low viscosity mastic |
|
Weight/gallon 11.6 lbs. |
| Color Light beige |
|
Flashpoint >200°F. |
| Solids 67% |
|
Freeze/thaw stability Stable |
| Viscosity 100,000 cps |
|
pH5.0 |
| Storage life 12 months in tightly closed containers at 75°F. |
|
|
|
|
|
Application Guidelines |
|
Application temperatureOver 50°F and below 90°F for adhesive and substrates.
Service temperatures 0°F. to 110°F.
Method of application V-notch trowel 3/16" wide x 1/4" deep, spaced 1/2" c.c.
Coverage 50 sq. ft. per gallon
Working time 20 minutes at 70°F.
Working surfaces Surfaces must be dry and free of any material that may deter adhesion, including severe and thick amounts of drywall joint compound. Patch large holes and depressions and remove any bumps or high spots, dust, oil, and grease. Concrete surfaces must be well cured and completely dry. Cut and pre-fit all panels. Lay fiberglass panels flat and let them acclimate to room temperature 24 hours before installing. Note: Panels used in conjunction with channel moldings should NOT fit tightly into the moldings. Leave a small gap under the molding for expansion and follow panel manufacturer’s recommendations. Any holes drilled through the panels for fasteners, pipes or conduits should be oversized to allow for natural movement of the panel. Click for FRP Installation Guide.
Cleanup Tools and excess adhesive may be cleaned with water while wet. If adhesive has dried, use mineral spirits. Follow solvent vendor's precautions when using solvents. NOTE: Test solvent in an out-of-the-way area to make sure it will not mar or attack the surface.
| Meets GreenSeal GS-36, LEED, SCAQMD, CARB and NAHB Green Building specifications. FDA
and Canadian Food Inspection Agency (CFIA) approved for indirect food contact. |
|
|
|
|
Product Features |
|
Environmentally safe - VOC-compliant
Quick grab - Minimal bracing
Nonflammable - No offensive odor
Bond FRP to many common porous building materials
Cleans easily with water in wet state
|
|
|
|
Limitations |
|
For best results, store GREENchoice Fast Grab FRP Adhesive above 50°F. Do not use over treated plywood or metal, plastic, foam board, painted surfaces, sealed concrete, certain types of specially treated or moisture resistant gypsum wallboard, or other non-porous surfaces. For these substrates, for use on freezers, and any other application other than FRP, call Tech Service at 1-888-533-9043. KEEP FROM FREEZING. |
|
|
|
Caution Statement |
|
CAUTION: EYE AND SKIN IRRITANT. Do not swallow. Do not allow eye contact or prolonged skin contact. FIRST AID: If swallowed, do not induce vomiting; contact physician. If eye contact occurs, flush eyes with water for 15 minutes. Wash skin contact areas with soap and water. If irritation from eye or skin contact areas persists, contact physician. For additional nformation, refer to Material Safety Data Sheet. KEEP OUT OF THE REACH OF CHILDREN. |
|
|
|
Ordering Information |
|
| Cat. No. |
Size |
Units per
Package |
Weight |
Packages
per Pallet |
|
| 4054 |
4 Gallon Pail |
1 |
49 |
36 |
| 4056 |
Gallon Can |
2 |
25 |
75 |
|
|
|
|
Important Notice: Our recommendations, if any, for
the use of this product are based on tests believed to be reliable. Since the use of this product is beyond
the control of the manufacturer, no guarantee or warranty, expressed or implied, is made as to such use or
effects incidental to such use, handling or possession or the results to be obtained, whether in accordance
with the directions or claimed so to be. The manufacturer expressly disclaims responsibility therefore.
Furthermore, nothing contained herein shall be construed as a recommendation to use any product in conflict
with existing laws and/or patents covering any material or use. |
©1999 Franklin International